Solve BECE Career Technology Questions & Answers

1. [1]

BECE mock · Career Technology

Kwasi was advised to practice good hygiene techniques and general composure by his mother. The statement above implies:

2. [1]

BECE mock · Career Technology

Which of these options is NOT likely to promote good grooming?

3. [1]

BECE mock · Career Technology

Which term is concerned with food handling, transport, proper storage of food and the actual processing of food material?

4. [1]

BECE mock · Career Technology

The investigation conducted uncovered that dry heat is the factor that led to Amina's injury. This means Amina's injury is:

5. [1]

BECE mock · Career Technology

To provide protection from the impact, dust and splashes, one needs to wear:

6. [1]

BECE mock · Career Technology

The type of fuel used in Ghana for meal preparation which has negative impact on the environment is:

7. [1]

BECE mock · Career Technology

A mortise and tenon joint was to be made by a J.H.S two students. During the process, a piece of wood was tested for the flatness and squareness. The flatness and squareness of the wooden workpiece was tested with:

8. [1]

BECE mock · Career Technology

A mortise and tenon joint was to be made by a J.H.S two students. During the process, a piece of wood was tested for the flatness and squareness. In making the tenon joints, the wood was cut both along and across the grain of the wood. Which tool is suitable for this operation?

9. [1]

BECE mock · Career Technology

A mortise and tenon joint was to be made by a J.H.S two students. During the process, a piece of wood was tested for the flatness and squareness. Double lines were marked as a guide for the deep hole to be cut. The tool for marking the double lines is the:

10. [1]

BECE mock · Career Technology

A mortise and tenon joint was to be made by a J.H.S two students. During the process, a piece of wood was tested for the flatness and squareness. To cut the deep hole in the wood, one must use:

11. [1]

BECE mock · Career Technology

Which of the following is NOT likely to be the reason for the selection of Acrylic for making the face of a wall clock?

12. [1]

BECE mock · Career Technology

Which of the following represents the front view in the direction of the arrow E?

13. [1]

BECE mock · Career Technology

The plan is represented by:

14. [1]

BECE mock · Career Technology

The end view is represented by:

15. [1]

BECE mock · Career Technology

Kwadwo failed to rub the teeth of a file with chalk before working with it. The file became blunt after a while. Which term describes the situation above?

16. [1]

BECE mock · Career Technology

In wooden work, which type of material is used to strengthen joints?

17. [1]

BECE mock · Career Technology

A pencil was used to mark the face side of planed wood. This indicates:

18. [1]

BECE mock · Career Technology

The type of line in technical drawing used to indicate the size of an object is:

19. [1]

BECE mock · Career Technology

For a tailor to hold a lining onto a fabric temporarily, he should use:

20. [1]

BECE mock · Career Technology

In designing a unit to solve a situation, the final solution must satisfy the:

21. [1]

BECE mock · Career Technology

Which of the following is commonly considered as second class protein?

22. [1]

BECE mock · Career Technology

A pregnant woman who has been attending antenatal was asked to eat iron-rich food for which of the reasons?

23. [1]

BECE mock · Career Technology

The type of vegetarians who neither eat the flesh nor product of animals are said to be:

24. [1]

BECE mock · Career Technology

Mortar is said to be batched in ratio. The ratio 1:3 means:

25. [1]

BECE mock · Career Technology

Which of the following tool has two spurs?

26. [1]

BECE mock · Career Technology

Thomas was asked to check the face alignment of a wall. Which of the following tool is suitable for the operation?

27. [1]

BECE mock · Career Technology

The figure above demonstrates which operation in walling?

28. [1]

BECE mock · Career Technology

The tool identified as x is:

29. [1]

BECE mock · Career Technology

The tool identified as y is:

30. [1]

BECE mock · Career Technology

The purpose of z in the wall is to:

31. [1]

BECE mock · Career Technology

A tool in sewing designed to measure hems, waistbands, button placement is the:

32. [1]

BECE mock · Career Technology

An eye protection glasses when exposed to light changes colour. This means the material is:

33. [1]

BECE mock · Career Technology

Cheese, wrewre and agushie are the main source of:

34. [1]

BECE mock · Career Technology

In assembling and joining of metal piece, the soldering iron is required. The head of the soldering iron is always made of copper because:

35. [1]

BECE mock · Career Technology

A man was seen sanding a wood surface along the grain with a material. The term that describes the operation is:

36. [1]

BECE mock · Career Technology

A man was seen sanding a wood surface along the grain with a material. The purpose of the sanding operation is:

37. [1]

BECE mock · Career Technology

The type of file identified above is the:

38. [1]

BECE mock · Career Technology

The file identified is the only file with:

39. [1]

BECE mock · Career Technology

The part marked A is the:

40. [1]

BECE mock · Career Technology

The part marked B is the:

41. [1]

BECE mock · Career Technology

Mrs. Mensah has decided to surprise her family by preparing ofam. State the suitable method for preparing ofam.

42. [3]

BECE mock · Career Technology

Highlight three table etiquettes a person should observe whenever eating at a table for a meal.

43. [2]

BECE mock · Career Technology

Discuss table etiquette.

44. [4]

BECE mock · Career Technology

There are two methods of sawing wood. State the two methods of sawing wood and differentiate them.

45. [1]

BECE mock · Career Technology

Study the solid figure shown. Name the solid figure.

Career Technology — Palm & Cedar March 2026 Career Technology

More Career Technology